Need some help here 450 And the JRXP6102

[Trex Pilot]

I thought i had this figured out but i guess not,If there is anyone out there that flys there 450 with the JR XP6102 TX how do you have your's set up like pitch curves and Gyro Gain such?my tail is all over the place and dont know why, and my pitch is out of wack,it was flying good yesterday i think i played with the wrong cotrolls on my TX :blockhead: and forgot how i had it set.Can you give me the details on how to set this up and pictures would be great. thanks

[CSpaced]

What gyro are you using? What exactly do you mean by "out of whack" on the pitch?

[Trex Pilot]

What gyro are you using? What exactly do you mean by "out of whack" on the pitch?
GYro is the GY401 and i cant get the pitch and throttle curse set right in normal mode i am not doing 3D yet and i dont no how to set my Gyro gain

[CSpaced]

On the 401 you have two cables, one plugged into the rudder and one plugged into an aux channel. To set the gain remotely you use the travel adjust/end point adjust on the radio that matches the channel you plugged that second cable into. If I remember correctly, 0 to 100 is heading hold and -100 to 0 is rate mode. Mine is set to +37 for HH and -33 for rate mode.

My throttle curve for normal mode is 0-70-100, and for Idle up is 100-90-100. My pitch curve is linear in all modes, 0-50-100 and is mechanically set to be 0 pitch at mid stick (which means you hover around 3/4 stick) You may want to increase the midlle setting until you can hover around mid stick.

[Trex Pilot]

On the 401 you have two cables, one plugged into the rudder and one plugged into an aux channel. To set the gain remotely you use the travel adjust/end point adjust on the radio that matches the channel you plugged that second cable into. If I remember correctly, 0 - 100 is heading hold and -100 to 0 is rate mode. Mine is set to +37 for HH and -33 for rate mode.

My throttle curve for normal mode is 0-70-100, and for Idle up is 100-90-100. My pitch curve is linear in all modes, 0-50-100 and is mechanically set to be 0 pitch at mid stick (which means you hover around 3/4 stick) You may want to increase the midlle setting until you can hover around mid stick.
I got it thanks i will let you know how she is in a minute :)

[Trex Pilot]

OK she is flying really smooth now :) but the tail is still waggin alittle kinda kickin alittle to thr right and back :( can you show me what the settings look like for setting the gyro? kinda like this:

[CSpaced]

I don't have the same radio so I can't show you the settings. Try increasing the travel adjustment a few percent and see what effect it has on the heli. If it wags more then go the other way. A little trial and error and you should be able to dial out the wag.

[Trex Pilot]

STill wagging it is fine in rate mode but in HH mode the tails is wagging back and forth about an 1/2 inch.

[Trex Pilot]

think ya might be able to help if you looked at this manual?
http://www.robotmarketplace.com/images/jrp6644-manual.pdf

[CSpaced]

STill wagging it is fine in rate mode but in HH mode the tails is wagging back and forth about an 1/2 inch.

Did you go through the entire range on the end points? If it didn't change anything make sure that you're adjusting the correct channel relative to where the gyro is plugged into.

[Trex Pilot]

I got her flying solid as a rock now thanks, i had to adjust the points for the Gear i was doing it for the rudder

[CSpaced]

Oh okay awesome, glad you got it sorted.

[Trex Pilot]

Oh okay awesome, glad you got it sorted.
I did with your help thanks again